PV Powered PVP2000 Скачать руководство пользователя страница 62

Страница: 62 / 84

Inverter

without

an Integrated AC/DC Disconnect

1. Determine the polarity of DC conductors coming from the PV array.

J10 Port with

GFI Negative Jumper

Figure B-7 PV Terminals in the Inverter

2. Install the DC positive conductor from the PV array into the PV

positive (+) terminal on the inverter Power Board.

3. Install the DC negative conductor from the PV array into the PV

negative (-) terminal on the inverter Power Board.

4. Locate the pre-installed negative GFI jumper into port J10. Remove

the negative jumper and replace with a positive ground jumper.

Negative GFI

Positive GFI

Figure B-8 Negative and Positive GFI Jumpers

WARNING

Do not connect or disconnect the GFI jumper shown in

Figure C-1 while the inverter is supplied with DC or AC

power.

AVERTISSEMENT

Ne pas connecter ou déconnecter la bretelle du différentiel

présenté à la Figure C-1 lorsque l’onduleur est alimenté en

CC ou CA.

Resume the installation procedures.

PV+
receives
DC- from
array

PV-
receives
DC+ from
array

Содержание PVP2000





















































































Результаты поиска

Содержание PVP2000

Отзывы:

Похожие инструкции для PVP2000

Бренды по названию

Популярные бренды

PV Powered PVP2000, Руководство по установке и эксплуатации

Результаты поиска

Содержание PVP2000

Отзывы:

Похожие инструкции для PVP2000

Бренды по названию

Популярные бренды