background image

PV Grid-tied Residential Inverter and Integrated AC/DC Disconnect

Installation and Operation Manual

41

7.3  Replacing the Inverter

1.  Remove the screws and the lid on the replacement inverter.
2.  Place the replacement inverter on the mounting bracket.
3.  Replace the three mounting screws in the lower section of the inverter 

assembly to secure the inverter to the mounting bracket.

4.  Reinstall each of the fittings with their locking nuts in the knockouts 

for the conductors.

Wiring the Replaced Inverter to the Disconnect

The disconnect connections are arranged in the following configuration 

(refer to Figure 4-2):
•  The left side is dedicated to AC
•  The right side is dedicated to DC

DC Connections

To wire the DC conductors from the disconnect to the replaced inverter:
1.  Route the DC conductors through the correct fitting and into the 

inverter.

2.  Connect the DC conductors to the DC wiring terminals inside the 

inverter. 
•  Connect positive to positive
•  Connect negative to negative
•  GEC is terminated at the grounding lug

Note: 

The DC conductors are reversed when running from the 

disconnect to the inverter. For example, the PV+ EGC is the 

left DC terminal in the disconnect but is the right terminal in 

the inverter.

AC Connections

To wire the AC connections from the disconnect to the replaced inverter:
1.  Route the AC conductors through the correct fitting and into the 

inverter. 

2.  Complete the following connections by:

•  Connecting the EGC conductor to the GND terminal. 
•  Connect the conductor coming from L2 in the disconnect to the 

terminal marked Line 2 inside the inverter. (For the PVP1100 this 

is the neutral conductor.)

•  Connect the conductor coming from L1 to the terminal marked 

Line 1 inside the inverter. 

Содержание PVP2000





















































































Отзывы: