PV Powered PVP2000 Скачать руководство пользователя страница 39

Страница: 39 / 84

PV Grid-tied Residential Inverter and Integrated AC/DC Disconnect

Installation and Operation Manual

Note:

An exception exists if a dedicated PV system AC sub-panel is

used to combine multiple inverters. The dedicated PV system

AC sub-panel requires a single breaker at the main utility

service panel for a multiple inverter installation.

Preparing for Wiring Multiple AC/DC Disconnects

The wiring raceway in the AC/DC disconnect allows a continuous run

of the AC, DC and system ground conductors between multiple inverter/

disconnect units.
1.  Make sure each disconnect ON/OFF switch is in the OFF position.
2.  Remove the screws from the lid of each disconnect.
3.  Remove the side knockouts on each disconnect to access the wiring

raceway.

4. Insert a fitting in each knockout opening so a continuous, water-tight

connection is created between each disconnect.

5. Route the AC, DC and the system ground conductors through each

disconnect, terminating applicable connections.

For instructions on connecting the PV array and the AC conductors inside

the disconnect, refer to the section

Wiring a Single Inverter with an

Integrated AC/DC Disconnect on page 21.

Connecting the Ground Conductors of Multiple Units

System grounding requirements for a multiple unit system also uses a

single-point ground.
1. Connect the EGC coming from the first PV array to the grounding lug

inside the disconnect cabinet of the first unit.

2. Connect the remaining units with a continuous EGC, branching from

grounding lug to grounding lug.

3. On each unit, connect the EGC from the utility grid to the grounding

terminal of the AC connection.

Содержание PVP2000





















































































Результаты поиска

Содержание PVP2000

Отзывы:

Похожие инструкции для PVP2000

Бренды по названию

Популярные бренды

PV Powered PVP2000, Руководство по установке и эксплуатации

Результаты поиска

Содержание PVP2000

Отзывы:

Похожие инструкции для PVP2000

Бренды по названию

Популярные бренды