manualshive.com logo in svg

PV Powered PVP2000, Руководство по установке и эксплуатации, Страница: 52 / 84

Поделиться
Скачать
PV Powered PVP2000 Скачать руководство пользователя страница 52

40

These connections include:
•  AC connection terminal
•  DC connection terminal
•  External Ground Fault Interrupt fuse

Review the following figure for the terminal locations.
The inverter is connected to the electrical grid using three wires: Line 1, 

Line 2 and GEC.

Figure 7-1  Connections between the Inverter and Integrated AC/DC Disconnect

7.2  Removing the Inverter

1.  Disconnect the AC and DC conductors, including the GEC at the 

grounding lug, inside the inverter.

2.  Pull all conductors down through the appropriate fitting to the wiring 

raceway inside the disconnect.

3.  Remove the locking nuts on the conduit fittings between the inverter 

and the disconnect units.

4.  Remove the three mounting screws in the lower section of the inverter 

assembly to detach the inverter from the mounting bracket.

5.  Lift the inverter from the mounting bracket.
6.  Replace the lid on the inverter.

AC/DC Disconnect Grounding Lug

Knockout for DC

Inverter 
Grounding Lug

DC Conductor 
Connections

AC Conductor 

Connections

AC Conductor 

Connections

Knockout for 

Data Comm

DC Conductor 
Connections

Dividers

Knockout for AC

Содержание PVP2000





















































































Отзывы:

Нет отзывов