PV Powered PVP2000 Скачать руководство пользователя страница 41

Страница: 41 / 84

5. Operation

WARNING

Before turning on the inverter, ensure that the inverter and

disconnect front covers are closed properly.

AVERTISSEMENT

Avant de mettre l’onduleur sous tension, s’assurer que les

panneaux avant de l’onduleur et du dispositif de déconnexion

sont adéquatement fermés.

WARNING

The heat sink can reach temperatures in excess of 158ºF (70ºC).

Do not touch the heat sink when in use, and do not place

anything on top of the heat sink.

AVERTISSEMENT

Le dissipateur thermique peut atteindre des températures

supérieures à 70ºC (158ºF). Ne pas toucher le dissipateur

thermique lorsqu’il fonctionne et ne placer aucun objet sur le

dessus.

5.1 Start Up Procedures

To start up the inverter, complete the following steps in the order

indicated.

NOTE: All steps are assumed completed in previous sections;

including but not limited to:
•  PV array open circuit voltage calculation
•  Checking the system for ground faults
•  Verifying the PV conductors are the correct polarity

1. Switch the main AC circuit breaker in the main utility panel to ON.
2. Use your voltmeter to verify the AC voltage is within the AC

Operating range indicated in Appendix A.

3. Turn the AC/DC Disconnect ON/OFF switch to the ON position.

WARNING

Before turning on the inverter and AC/DC Disconnect, ensure

that the front panel is closed properly and the lid’s screws are

tightened.

OPERA

TIONS

Содержание PVP2000





















































































Результаты поиска

Содержание PVP2000

Отзывы:

PV Powered PVP2000, Руководство по установке и эксплуатации, Страница: 41 / 84

Результаты поиска

Содержание PVP2000

Отзывы: