PSI PP 2024 Скачать руководство пользователя страница 60

Страница: 60 / 116

Intelligent Paper Stacker iPS 2024

7-3

7-4

7.1.3

Paper Exit Tray Assembly

7.1.4

The Pendulum

The frame (9) between the two vertical bars (10) bears the paper exit tray (2):

The pendulum is to be mounted such that the gear points to the left with the

Push the tray (2) from the front underneath the bar (12) into the frame.

Align the tray's bar (11) with the bar (12) of the frame (9) such that the screw
holes fit to each other.

Insert the allen head screws (5) from the top and turn them until they dig into

the thread of the bar (11). Use the enclosed allen wrench to tighten the

screws.

bent sheet metal guides to the top.

Insert the pendulum through the opening in the table from the bottom

Push the axis into the bush (22) at the left.

Press the axis to the bush (22) until it snaps into the bush (23) at the right.

Note:

The position of the pendulum is arbitrary. After power on the stacking
system moves the pendulum automatically into the right starting position.

Содержание PP 2024





















































































































Результаты поиска

Содержание PP 2024

Отзывы:

Бренды по названию

Популярные бренды

PSI PP 2024, Руководство пользователя

Результаты поиска

Содержание PP 2024

Отзывы:

Бренды по названию

Популярные бренды