PSI PP 2024 Скачать руководство пользователя страница 34

Страница: 34 / 116

Configuring the Printer

3-17

3-18

3.6

Configuration Programs

3.6.2

Profiler

The following programs for printer configuration are available:

available.

Profiler

The first step is to select the Profiler for the actual printer. Use the pull down

A program for easy programming of all print job specific parameters into

PRINTER

to select

PP 2024

Profiles

Profile Selector

For easy selection of one predefined profile.

Note:

Both programs are running under Windows 95/98 and NT 4.0.

3.6.1

Installation

Follow the standard procedures:

For installation of the English version of the Profiler from the CD select in the

In the Profiler the following menus are available:

Windows Start Menu the function

Run ...

and type the command:

General Menu

D:\profiler\install\usa\disk1\setup.exe

Emulations Menu

For installation of the English version of the Profile Selector from the CD

Note:

This three menus are available for all profiles.

select in the Start Menu the function

Run ...

and type the command:

D:\selector\install\usa\disk1\setup.exe

Note:

In both examples the letter

is used for the CD-ROM drive.

After installation both programs are listed in the screen

Programs

of the

Windows Start Menu.

For easy handling of the Profiler an online help text for each menu item is

Paper Menu

General Menu:

Содержание PP 2024





















































































































Результаты поиска

Содержание PP 2024

Отзывы:

Бренды по названию

Популярные бренды

PSI PP 2024, Руководство пользователя

Результаты поиска

Содержание PP 2024

Отзывы:

Бренды по названию

Популярные бренды