PRÜFTECHNIK VIBSCANNER VIB 5.400 Скачать руководство пользователя страница 73

Страница: 73 / 76

VIBSCANNER 11.2010

Troubleshooting

• Symptom:
Battery does not charge (red LED on the battery does not
light up) when the charger is connected and VIBSCANNER
is switched off.

Meaning:
VIBSCANNER erroneously sends a starting signal to the
battery.

What to do:
Remove the battery from VIBSCANNER and charge it
separately.

• Symptom:
Charging process terminates prematurely (5min – 1h),
green LED lights up on the battery.

Meaning:
Deeply discharged battery.

What to do:
Switch on VIBSCANNER without the charger connected.
Leave it switched on until the battery is empty again and
VIBSCANNER switches off by itself. Then repeat the charg-
ing process. If necessary, charge the battery separately.

• Symptom:
“Battery level inaccurate” appears when switching off or
the display of the level of charge is obviously wrong.

Meaning:
Charge electronics must be newly programmed.

What to do: see page 11

• Symptom:
VIBSCANNER housing is dirty.

What to do:
Clean the VIBSCANNER housing using a lint-free cloth and
a commercial household detergent.

Clean the VIBSCANNER display using window cleaner and
a cloth or an absorbent kitchen roll.

When cleaning the instrument, make sure that the
battery plugged into the instrument and the dust
protection caps cover the connector sockets.

Attention!

Содержание VIBSCANNER VIB 5.400













































































Результаты поиска

Содержание VIBSCANNER VIB 5.400

Отзывы:

Похожие инструкции для VIBSCANNER VIB 5.400

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBSCANNER VIB 5.400, Руководство по эксплуатации

Результаты поиска

Содержание VIBSCANNER VIB 5.400

Отзывы:

Похожие инструкции для VIBSCANNER VIB 5.400

Бренды по названию

Популярные бренды