ProMinent Sigma / 2 Basic Type SBKa Скачать руководство пользователя страница 7

Страница: 7 / 52

Observe the general limitations with regard to viscosity limits, chem‐

ical resistance and density - see also ProMinent Resistance List (in

the Product Catalogue or at www.prominent.com/en/downloads)!

All other uses or modifications are prohibited.

Never operate pumps without the relevant nameplate (and the respec‐

tive EC Declaration of Conformity) for pumps for use in atmospheres

at risk from explosion in atmospheres potentially at risk from explo‐

sion.

The pump is not intended for the metering of gaseous media or solids.

The pump is not intended for the metering of flammable feed chemi‐

cals.

The pump is not intended to meter explosive substances and mix‐

tures.

The pump is not intended for unprotected outside use.

The pump is only intended for industrial use.

The pump should only be operated by trained and authorised per‐

sonnel.

Observe the information contained in the operating instructions at the

different phases of the device's service life.

Action

Qualification

Storage, transport, unpacking

Instructed person

Assembly

Technical personnel, service

Planning hydraulic installation

Qualified personnel who have a

thorough knowledge of oscillating

diaphragm pumps.

Hydraulic installation

Technical personnel, service

Installation, electrical

Electrical technician

Operation

Instructed person

Maintenance, repair

Technical personnel, service

Decommissioning, disposal

Technical personnel, service

Troubleshooting

Technical personnel, electrical

technician, instructed person,

service

Explanation of the terms:
Technical personnel
A qualified employee is deemed to be a person who is able to assess the

tasks assigned to him and recognise possible dangers based on his/her

technical training, knowledge and experience, as well as knowledge of

pertinent regulations.
Note:
A qualification of equal validity to a technical qualification can also be

gained by several years employment in the relevant work area.
Electrical technician
Electrical technicians are deemed to be people, who are able to complete

work on electrical systems and recognise and avoid possible dangers

independently based on their technical training and experience, as well as

knowledge of pertinent standards and regulations.
Electrical technicians should be specifically trained for the working envi‐

ronment in which they are employed and know the relevant standards and

regulations.
Electrical technicians must comply with the provisions of the applicable

statutory directives on accident prevention.
Instructed person

Qualification of personnel

Safety chapter

Содержание Sigma / 2 Basic Type SBKa





















































Результаты поиска

Содержание Sigma / 2 Basic Type SBKa

Отзывы:

Похожие инструкции для Sigma / 2 Basic Type SBKa

Бренды по названию

Популярные бренды

ProMinent Sigma / 2 Basic Type SBKa, Руководство по эксплуатации

Результаты поиска

Содержание Sigma / 2 Basic Type SBKa

Отзывы:

Похожие инструкции для Sigma / 2 Basic Type SBKa

Бренды по названию

Популярные бренды