ProMinent OZLa 06 O Скачать руководство пользователя страница 23

Страница: 23 / 72

Assembly and installation

User qualification, installation: trained and qualified personnel

Chapter 3.4 ‘User qualification’ on page 12

User qualification, hydraulic installation: trained and qualified

personnel

Chapter 3.4 ‘User qualification’ on page 12

User qualification, electrical installation: electrical technician

Chapter 3.4 ‘User qualification’ on page 12

6.1 Safety guidelines and general requirements

WARNING!
Fatal injury by electrocution.
The system produces high voltage.
– For safety reasons, only allow appropriately

qualified technical personnel to install, operate

and service this system.

– Ensure that all technical personnel are trained

by the manufacturer about the specific system.

Unauthorised personnel handling the system can

result in severe injury to personnel or even death.

WARNING!
Fatal injury by the leakage of toxic gas.
The system generates highly concentrated (up to

150 g/Nm

), compressed (up to 2 bar) ozone gas

from air or pure or enriched oxygen.
– For safety reasons, only allow appropriately

qualified technical personnel to install, operate

and service this system.

– Ensure that all technical personnel are trained

by the manufacturer about the specific system.

Unauthorised personnel handling the system can

result in injury to personnel or even death.

6.2 Recommendations regarding the suitability of the system's installation place

WARNING!
Danger caused by operation of the system in

unsuitable locations.
– Adhere to all national and local regulations

relating to the use of oxygen and ozone.

– The operator of the ozone generation system is

responsible for ensuring that the regulations

are implemented.

Failure to observe the safety instructions can result

in injuries to personnel and material damage.

Assembly and installation

Содержание OZLa 06 O









































































Результаты поиска

Содержание OZLa 06 O

Отзывы:

Бренды по названию

Популярные бренды

ProMinent OZLa 06 O, Руководство по эксплуатации

Результаты поиска

Содержание OZLa 06 O

Отзывы:

Бренды по названию

Популярные бренды