manualshive.com logo in svg

ProMinent gamma/ L, Руководство по эксплуатации, Страница: 43 / 81

Поделиться
Скачать
ProMinent gamma/ L Скачать руководство пользователя страница 43

Pr

o

Minent

®

Page 33

Repairs

TAKE CARE

•

The leakage hole must point downwards when the pump is fully assembled
(see fig. 23).

•

Position the top plate (4) correctly on the pump housing (6). Do not distort
the top plate on the pump housing , otherwise the safety diaphragm (5) will
not fit.

S

Lay the diaphragm (3) into the top plate (4).

S

Hold the top plate and screw the diaphragm (3) in a clockwise direction until it is firmly in
position (you will feel the resistance of the return spring).

TAKE CARE

•

Do not overtighten the diaphragm (3).

•

The top plate (4) must remain in position to prevent the safety diaphragm (5)
from distorting.

S

The top plate (4) must remain in position to prevent the safety diaphragm (5) from distorting.

S

Position the liquid end (2) with the screws (1) on the diaphragm (3) and the top plate (4) (the
priming connector must point downwards once the pump is fully assembled).

S

Screw on screws (1) lightly and tighten (starting torque, see above).

S

For coarse/fine bleed versions: ensure the liquid end cover engages in the liquid end, then
push the coarse/fine bleed (knob) into the liquid end.

1

2

3

4

5

6

Fig. 30

1 Screws

4 Top plate

2 Liquid end

5 Safety diaphragm

3 Diaphragm

6 Pump housing

GUIDELINE

•

Check the screw torque after 24 hours in operation!

•

For PP liquid ends recheck the screw torque after three months!

Содержание gamma/ L


















































































Отзывы:

Нет отзывов