ProMinent gamma/ L Скачать руководство пользователя страница 26

Страница: 26 / 81

Minent

Page 16

Settings

7.3

Select operating mode (MODE menu)

The following operating modes are selected via the MODE menu (depending upon identity code,
some operating modes may be absent):

•

Manual: for operation by hand
(Identity code, control variant: manual, standard option)

•

Analogue: for electronic control
(Identity code, control variant: analogue current)

•

Contact: for contact operation
(Identity code, control variant: external 1:1 / external with pulse control)

•

Batch: for batch operation
(Identity code, control variant: external with pulse control)

Continuous

display

Batch

Contact

Manual

Analog

7.4

Settings for operating mode (SET menu)

In the SET menu you can adjust various settings depending upon the selected operating mode.

The following programmable function settings menus appear in all operating modes:

•

Calibrate (CALIB menu)

•

Pressure levels (PRESS menu)

•

Auxiliary frequency (AUX menu)

•

Flow (FLOW menu, available only if flow monitor is connected)

Содержание gamma/ L


















































































Результаты поиска

Содержание gamma/ L

Отзывы:

ProMinent gamma/ L, Руководство по эксплуатации, Страница: 26 / 81

Результаты поиска

Содержание gamma/ L

Отзывы: