manualshive.com logo in svg

Pro-face FP3900-T41, Руководство пользователя

Поделиться
Скачать
Pro-face FP3900-T41 Скачать руководство пользователя страница 69

FP-3900T Series User Manual

6-2

6.1

Troubleshooting

6.1.1

Possible Device Problems

This chapter explains the main method of dealing with the trouble in the use of the FP.

Possible types of trouble while using this unit are as follows.

No display

•

No display appears after the unit is switched on. 

•

The screen disappears during standard operation.

•

The screen does not display normally.

Touch panel does not respond

•

The touch panel does not respond when pressed. Its reaction time is abnormally long.

•

For problems other than problems of the FP, please refer to the manual of each equipment.

To prevent an electric shock, be sure the power cord is not connected when wiring the unit.

• This section assumes that the FP is the cause of a problem, not the host. When 

the host is the problem, please refer to its corresponding manual.

Содержание FP3900-T41
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды