manualshive.com logo in svg

Pro-face FP3900-T41, Руководство пользователя

Поделиться
Скачать
Pro-face FP3900-T41 Скачать руководство пользователя страница 55

FP-3900T Series User Manual

4-2

4.1

Operation Mode Setup

4.1.1

Preset Settings and Adjustments for Dip Switch and Slide Switch 

The Dip Switches and Slide Switch are located in the bottom of the FP unit. Loosen the screws of the cover 

with a Phillips head screwdriver and then remove the cover. After setting the dip switches and slide switches, 

reinstall the cover and screws with the screwdriver. The tightening torque for those screws is 0.5 ~ 0.6 N•m. 

Only the settings when the power supply is turned on is effective to the Dip Switches and the Slide Switch. 

After changing the settings of the Dip Switches and the Slide Switch, be sure to restart your FP unit.         

The factory default for the FP unit’s Dip Switches and Slide Switch are as follows.

„

SW1

•

SW1-2

 

Dip Switch SW1-2 is used to display or hide the OSD.

 

To hide the OSD, set the switch to ON. To display the OSD, set the switch to OFF.

 

The default setting is OFF. (OSD is displayed.)

SW1-1

Reserved (Always OFF)

SW1-2

Display/Hide the OSD

SW1-3

Reserved (Always OFF)

SW1-4

Reserved (Always OFF)

SW1-5

Reserved (Always OFF)

SW1-6

Reserved (Always OFF)

SW1-7

Reserved (Always OFF)

SW1-8

Reserved (Always OFF)

Dip Switches (SW1)
Slide Switch (SW2)

Bottom

Cover

1

2

3

4

5

6

7

8

ON

Содержание FP3900-T41
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды