manualshive.com logo in svg

Pro-face FP3900-T41, Руководство пользователя

Поделиться
Скачать
Pro-face FP3900-T41 Скачать руководство пользователя страница 36

Chapter 2 Specifications

2-15

2.5

Names and Functions

A:TFT Color LCD

 

The display monitor for your host unit.

B:Touch Panel

 

Allows you to switch screens or write data to the host.

C:Power Connector (socket)  

 

Provides the input and ground terminals for a power 
cable.

D:Setting Switch

 

By opening the cover, the Dip switches and slide 
switch are seen. Each switch can set a operation mode.

E:Analog RGB Connector

 

Connector for analog RGB interface

F: DVI-D Interface Connector

 

Connector for DVI-D interface

G: Serial Connector

 

Connector for Serial (RS-232C) interface. Used for 
sending touch panel data to between the hosts.

H:USB Connector (Type B)

 

Connector for USB interface. Used for sending touch 
panel data to the hosts, or used as an upstream port for 
USB-HUB.

I: Front LED

 

Used to indicate the condition of the power supply, a 
backlight burnout or image signal input.

J: Front USB Connector (Type A)(FP3900-T41-U only)

 

A downstream port for embedded USB-HUB  in 
conformity with USB2.0/1.1 standard, which is used 
for connecting USB devices. Connect the USB 
connector (H:USB connector) and Host PC for Front 
USB connector use.

Rear

Bottom

A,B

C

D

E F G

H

J

I

SEE

4.1 Operation Mode Setup (page4-2)

SEE

4.1.2 Status of Front LED in Operation 

Modes (page4-3)

Содержание FP3900-T41
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды