manualshive.com logo in svg

Pro-face FP3900-T41, Руководство пользователя

Поделиться
Скачать
Pro-face FP3900-T41 Скачать руководство пользователя страница 62

Chapter 4 Setting up and Adjusting the FP unit

4-9

Resets all the settings and then returns to the top menu.

Cancels the setting and then returns to the top menu.

Applies the setting and then returns to the top menu.

Cancels the setting and then returns to the top menu.

All Reset

Input Source

Applies the setting and then returns to the top menu.

Cancels the setting and then returns to the top menu.

Applies the setting and then returns to the top menu.

Cancels the setting and then returns to the top menu.

Auto Adjust (Analog RGB only)

Auto Gain (Analog RGB only)

• Be sure to perform the auto adjust while things except the 

black are displayed on the edge of the screen.

• Be sure to perform the auto gain control when the screen 

has both 100% black and 100% white areas displayed.

Icon decision

Icon selection

Saves the setting and quits the OSD.

End of OSD

Saves all the adjusted settings in the EEPROM.

Содержание FP3900-T41
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды