Pro-face FP3900-T41 Скачать руководство пользователя страница 49

Страница: 49 / 79

FP-3900T Series User Manual

3-8

Wiring

Use the following wiring for FP. Those are Phoenix Contact products.

Connecting the Power Cord

When connecting the AC type power cord, be sure to follow the procedures given below.

(1)

Confirm that the power cord is unplugged from the power supply.

(2)

Push the Opening button by a small and flat screw driver to open the desired pin hole.

(3)

Insert each pin terminal into its each hole. Release the Opening button to clamp the pin place.

(4)

After inserting all three pins, insert the Power Plug into the Power Connector at FP. Fix the plug with

two(2) minus screws.

Recommended Drivers

SZS 0.6X3.5 (1205053)

Recommended stick end terminal

AI 0.75-10GY(3201288)

AI 1-10RD(3200182)

AI 1.5-10BK(3200195)

AI 2.5-12BU(3200962)

Crimp tool for recommended stick end terminal

CRIMPFOX ZA 3 (1201882)

• Confirm that all wires are connected correctly.

• The torque required to tighten these screws is 0.5 N•m - 0.6 N•m.

• To prevent the possibility of a terminal short, use a pin terminal that has an

insulating sleeve.

AC power supply cord

Opening Button

Содержание FP3900-T41
















































































Результаты поиска

Содержание FP3900-T41

Отзывы:

Бренды по названию

Популярные бренды

Pro-face FP3900-T41, Руководство пользователя

Результаты поиска

Содержание FP3900-T41

Отзывы:

Бренды по названию

Популярные бренды