Price FFU-HE Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 64

background image

FAN FILTER UNIT - HIGH EFFICIENCY

INSTALLATION & SERVICE INSTRUCTIONS

Troubleshooting Tips:

• If FFU is turned to 75% and it shut offs after a short time, follow the below steps:

1. Power cycle the FFU-HE.

2. Measure inlet static while the FFU-HE is running.

3. If the inlet static is positive, reduce your airflow device airflow an additional 25%.

4. Return to Step 4, above and finish balancing unit.

• If the unit shuts off still at this 50% setpoint, follow the below steps:

1. Power cycle the FFU-HE

2. Measure inlet static while the FFU-HE is running

3. If the inlet static is positive, reduce your airflow device airflow 25% more.

4. Return to Step 4, above and finish balancing unit.

If experiencing further issues with unit, contact Price Industries Fan Filter help at:

By Email: [email protected]

By Phone: (204) 654-5613 option 5

Low Air Velocity

1.  Check prefilter media (only with optional prefilter); replace or clean as necessary.
2.  Adjust variable speed control for higher blower output.
3.  Check power for proper voltage, amerage, and distribution frequency.
4.  Replace HEPA/ULPA filter if the veloicty remains low.

High Air Velocity

1. Adjust variable speed control for lower blower output.

Non-Laminar Flow and/or
Excessive Contamination

1. Ensure that no large obstructions are upstream of airlfow pattern.
2. Determine that no other air-moving devices are operating in or around cleanroom which could disrput the room's

airlfow pattern.

3. Check air velocity and if low, conduct the 'Low Air Velocity' procedure outlined above.
4. Conduct somke and photometer test on HEPA/ULPA filter. Seal or replace.

Motor Keeps Shutting Off

1.  Check if unit is ducted.
2.  If no, contact Price at [email protected].
3.  If yes, check inlet pressure, if postive, re-balance until inlet pressure is zero.

LED Light Turned Red

1. Refer to 'Motor Will Not Run' procedure outlined below.

LED light Turned Yellow

1. Replace filter.

Motor Will Not Run

1. Check that motor has power at correct voltage.
2. Check that the speed controller has power.

45

priceindustries.com | FAN FILTER UNIT - HIGH EFFICIENCY - Manual

«
...
45
46
47
48
49
...
»

Содержание FFU-HE Series

































































Отзывы:

Нет отзывов

Похожие инструкции для FFU-HE Series

Бренд: Quooker Страницы: 12

Бренд: Watts Страницы: 8

Бренд: Toro Страницы: 12

Бренд: Waterdrop Страницы: 2

STREET SMART MFS

Бренд: McNeilus Страницы: 8

CLI U12 SD0F1110 NG B/U

Бренд: Velux Страницы: 56

Бренд: Enapter Страницы: 2

Бренд: Alpine Страницы: 2

Бренд: Campbell Hausfeld Страницы: 12

Бренд: ITech Страницы: 14

MASTERSTREAM 1000 Series

Бренд: Task Force Tips Страницы: 8

CLARYUM AO-US-100-R

Бренд: A.O. Smith Страницы: 3

BRENNA HTW-07-B-C

Бренд: Hi-Tech Страницы: 6

Бренд: A.O. Smith Страницы: 20

Pure&Sure 329843-000_R0

Бренд: A.O. Smith Страницы: 40

Wafergard III NF-750

Бренд: entegris Страницы: 7

Spa & Pool UV-C 140000

Бренд: Certikin Страницы: 16

Бренд: P3 International Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды