Price FFU-HE Series Скачать руководство пользователя страница 27

Страница: 27 / 64

FAN FILTER UNIT - HIGH EFFICIENCY

INSTALLATION & SERVICE INSTRUCTIONS

Filter/Motor Indicator LED (ML/FL) – RSR

Sample line string below:

FFU-HE/24/48/

RSR

/BC/ECM/115/10//CT//HEPA//ECMDX//WK/DSW/PC/TMB/ATS/

/WPF/PL-AL/F-AL/PL-B12/F-B12

LED Operation

Option

Code

LED

Color

Action

Notes

Filter LED

Green

None

Indicates normal operation until filter pressure drop exceeds calibrat-

ed pressure drop (factory set at 1.5x clean filter pressure).

Yellow

Change Filter

Indicates filter pressure drop has exceeded calbirated setting (factory
set at 1.5x clean filter pressure.

Motor

LED

Green

None

Indicates normal motor operation when the static pressure is above
0.2" w.g.

Red

Troubleshoot Motor

Indicates motor is not in operation, and that unit static pressure is

below 0.2" w.g.

Calibration

Filter LED will come factory set to activate at the pressure drops listed in the Table below.

Filter

Pressure @ 90fpm [in w.g.]

1.5x Clean Filter [in w.g.]

HEPA

0.4

0.6

ULPA

0.6

0.9

If different set points are desired, they can be adjusted as follows:

STEP 1:

Remove Loctite from adjustment screw hole.

Filter Indicator Set Points

Pressure Switch Adjustment

priceindustries.com | FAN FILTER UNIT - HIGH EFFICIENCY - Manual

Содержание FFU-HE Series
































































Результаты поиска

Содержание FFU-HE Series

Отзывы:

Похожие инструкции для FFU-HE Series

Бренды по названию

Популярные бренды

Price FFU-HE Series, Руководство пользователя

Результаты поиска

Содержание FFU-HE Series

Отзывы:

Похожие инструкции для FFU-HE Series

Бренды по названию

Популярные бренды