Precor C542i Скачать руководство пользователя | Manualshive

Страница: 59 / 67

background image

C542i Elliptical Fitness Crosstrainer

Page 59

Procedure 7.19 - Replacing a Power Input Jack Assembly

1.

Remove the rear cover and disconnect the red battery lead from terminal M6 of the lower
PCA.

2.

Disconnect the J4 connector from the lower PCA. See Diagram 7.17.

Diagram 7.19 - Power Input Jack Mounting

3.

Remove the screws that fasten the power input jack mounting plate to the rear cover
support. See Diagram 7.19.

4.

Remove the power input jack mounting plate with the power input jack assembly from the
unit.

5.

Remove the nut that fastens the power input jack to the power input jack mounting plate.
Remove the power input jack from the power input jack mounting plate.

6.

Fasten the replacement power input jack to the power input mounting with the mounting nut
provided with the power input jack.

7.

Feed the power input jack wiring through the hole in the rear cover support and mount the
power input jack mounting plate with the screws removed in step 3.

8.

Route the power input jack wiring to the lower PCA. Connect the plug on the power input
jack wiring to the J4 connector on the lower PCA.

9.

Reconnect the red wire battery lead, removed in step 1, to the positive (+) terminal of the
battery.

10. Replace the rear cover.

Mounting Screw

Input Jack

Mounting Nut

Input Jack

Mounting Plate

«
...
57
58
59
60
61
...
»

Содержание C542i




































































Отзывы:

Нет отзывов

Похожие инструкции для C542i

Бренд: Weslo Страницы: 16

Бренд: Taurus Страницы: 44

Бренд: Proteus Страницы: 3

Бренд: NordicTrack Страницы: 28

IT8017 Super Pullover

Бренд: impulce 2 Страницы: 20

Бренд: Dyaco Страницы: 35

Бренд: Life Span Страницы: 47

NordicTrack COMMERCIAL 14.9

Бренд: ICON Страницы: 40

Бренд: ICON Health & Fitness Страницы: 32

Бренд: JetBlack Страницы: 2

Бренд: CAPITAL SPORTS Страницы: 152

Бренд: Sunny Health & Fitness Страницы: 18

Бренд: Sunny Health & Fitness Страницы: 15

Бренд: VIRTUFIT Страницы: 28

ELEVATE PULL-UP

Бренд: Total Gym Страницы: 12

Бренд: CardioStyle Страницы: 12

Бренд: Sole Fitness Страницы: 32

Бренд: Sole Fitness Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды