Precor C542i страница 53 Скачать руководство пользователя | Manualshive

Страница: 53 / 67

background image

C542i Elliptical Fitness Crosstrainer

Page 53

Procedure 7.16 - Replacing a Load Resistor

Warning

When the EFX is operated the load resistors get very hot. Be sure to allow the load resistors
enough time to cool before continuing with this procedure.

1.

Remove the rear cover and disconnect the red battery lead from terminal M6 of the lower
PCA.

2.

Remove the three screws that fasten the load resistor assembly and shield to the frame
upright. Rotate the load resistor assembly 180 degrees and set it on the top of the frame
upright. See Diagram 7.14.

Diagram 7.14 - Load Resistor Assembly

3.

Remove the screws that fasten the load resistor wiring from both terminals of the resistors.

4.

Remove the screw that fastens one of the load resistor clips to the mounting bracket.
Remove the resistor(s) being replaced.

5.

Slide the replacement resistor into its mounting position so that its terminals contact the
terminals of the other load resistor. Slide the load resistor clip, removed in step 4 into the
opposite end of both resistors and fasten the load resistor clip to the mounting bracket with
the screw removed in step 4.

6.

Reconnect the load resistor wiring removed in step 3. When compete the resistors should
be connected to each other with a load resistor wire connected to each terminal of the
resistors.

7.

Rotate the load resistor assembly back into its mounting position with the shield between
the load resistor and the frame upright. Fasten the load resistor assembly and shield to the

Load Resistor

Load Resistor Clip

Mounting Bracket

«
...
51
52
53
54
55
...
»

Содержание C542i




































































Отзывы:

Нет отзывов

Похожие инструкции для C542i

Бренд: TFI Страницы: 24

Бренд: NordicTrack Страницы: 36

Бренд: Xterra Страницы: 28

Бренд: fitness gear Страницы: 15

Бренд: Fitness Quest Страницы: 26

Бренд: Vision Fitness Страницы: 52

Бренд: York Fitness Страницы: 29

Pro-Form Carbon EL

Бренд: ICON Health & Fitness Страницы: 36

ELLIPTI-CYCLE 210

Бренд: Trojan Страницы: 20

SOLO 200 Care instructions and assembly

Бренд: Trojan Страницы: 20

Бренд: Spirit Commercial Страницы: 32

Бренд: Spirit Commercial Страницы: 48

STRIDE SELECT 830

Бренд: ProForm Страницы: 24

StrideClimber 831.23745.0

Бренд: ProForm Страницы: 28

StrideClimber 831.23745.1

Бренд: ProForm Страницы: 28

StrideSelect 600

Бренд: ProForm Страницы: 36

Бренд: MONSTER FITNESS Страницы: 16

Бренд: Movement Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды