Precision Digital Corporation PD765-6X0-00 Скачать руководство пользователя страница 7

Страница: 7 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

SPECIFICATIONS

Except where noted all specifications apply to operation at +25°C.

General

DISPLAY

Trident: 0.56" (14 mm), Trident X2: 1.20" (31 mm),
Four digits (-1999 to 9999), automatic lead zero blanking.

DISPLAY INTENSITY

Eight intensity levels

DISPLAY
UPDATE RATE

Process/RTD: 3.7-5/second
Thermocouple: 1.8-2.5/second

OVERRANGE

Display flashes

9999

UNDERRANGE

Display flashes

-1999

PROGRAMMING
METHODS

Four front panel buttons, PC and MeterView

software, or

cloning using Copy function

NOISE FILTER

Programmable from 2 to 199 (0 will disable filter)

RECALIBRATION

All ranges are calibrated at the factory. Recalibration is
recommended at least every 12 months.

MAX/MIN
DISPLAY

Max/min readings reached by the process are stored until
reset by the user or until power to the meter is turned off.

PASSWORD

Programmable password restricts modification of settings.

NON-VOLATILE
MEMORY

All programmed settings are stored in non-volatile memory
for a minimum of ten years if power is lost.

POWER
OPTIONS

85-265 VAC, 50/60 Hz
90-265 VDC, 20 W max
or 12-36 VDC, 12-24 VAC, 6 W max
See table for power consumption
(*X: number depends on option)

Model Watts

PD765-6RX-0* 8

PD765-6RX-1, 2*

PD765-7RX-0* 6

FUSE

Required fuse: UL Recognized, 5 A max, slow blow
Up to 6 meters may share one 5 A fuse

ISOLATED
TRANSMITTER
POWER SUPPLY

One or two transmitter power supplies (Optional)
P or P1: 24 VDC

10% @ 200 mA max. (-1 option)

P1 & P2: 24 VDC

10% @ 200 mA & 40 mA max. (-2 option)

NORMAL MODE
REJECTION

64 dB at 50/60 Hz

ISOLATION

4 kV input/output-to-power line
500 V input-to-output or output-to-P1/P2 supplies
-6R5 & -6X5 models only: 100 V output-to-24 VDC supply

OVERVOLTAGE
CATEGORY

Installation Overvoltage Category II:
Local level with smaller transient overvoltages than Instal-
lation Overvoltage Category III.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание PD765-6X0-00








































































Результаты поиска

Содержание PD765-6X0-00

Отзывы:

Похожие инструкции для PD765-6X0-00

Бренды по названию

Популярные бренды

Precision Digital Corporation PD765-6X0-00, Инструкция по эксплуатации

Результаты поиска

Содержание PD765-6X0-00

Отзывы:

Похожие инструкции для PD765-6X0-00

Бренды по названию

Популярные бренды