Precision Digital Corporation PD765-6X0-00 Скачать руководство пользователя страница 65

Страница: 65 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

TROUBLESHOOTING

For an

Interactive Virtual

Meter Demo

visit

tvm.predig.com

Due to the many features and functions of the meter, it’s possible that
the setup of the meter does not agree with what an operator expects to
see. If the meter is not working as expected, refer to the

Diagnostics

menu and consult the recommendations described below.

Diagnostics Menu (

diag

)

The

Diagnostics

menu is located in the

Advanced

Features Menu

, to ac-

cess

Diagnostics

menu see

Advanced Features Menu

, page 50.

It provides an easy way to view the programmed parameter settings for
troubleshooting purposes. Press the

Enter/Ack

button to view the set-

tings and the

Menu

button to exit at any time.

For a description of the diagnostics messages

see

Advanced Features

Menu & Display Messages, page 51.

Determining Software Version

To determine the software version of a meter:

1. Go to the

Diagnostics

menu (

diAG

) and press

Enter/Ack

but-

ton.

2. Press

arrow/

Max

button and scroll to Information menu

(

Info

3. Press

Enter/Ack

to access the software number (

SFT

), version

(

UER

). Write down the information as it is displayed. Continue

pressing

Enter/Ack

until all the information is displayed.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание PD765-6X0-00








































































Результаты поиска

Содержание PD765-6X0-00

Отзывы:

Похожие инструкции для PD765-6X0-00

Бренды по названию

Популярные бренды

Precision Digital Corporation PD765-6X0-00, Инструкция по эксплуатации

Результаты поиска

Содержание PD765-6X0-00

Отзывы:

Похожие инструкции для PD765-6X0-00

Бренды по названию

Популярные бренды