Precision Digital Corporation PD765-6X0-00 Скачать руководство пользователя страница 35

Страница: 35 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

Calibrating the Meter (

Cal

)

To scale the meter without a signal

source, refer to Scaling the Meter

(

scal

), page 33.

The meter can be calibrated to display the process in engineering units
by applying the appropriate input signal and following the calibration
procedure.
The use of a calibrated signal source is strongly recommended to cali-
brate the meter.

Recalibrating Temperature Inputs (

Cal

)

Remember, the meter is

calibrated

at the factory prior to shipment. Re-

calibration is recommended at least every twelve months.
The

Calibration

(

CAL

) menu is used to

recalibrate

the thermocouple and

RTD inputs.

Allow at least 30 minutes warm-up time

before performing recalibration proce-

dure to ensure specified accuracy.

inp1

dis1

4.00

Set Display 1

Value

inp2

Calibrate

Input 2

Cal

Display

Flashes

Accepting

Input

See

Scaling the Meter

for Button

Functions Description

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание PD765-6X0-00








































































Результаты поиска

Содержание PD765-6X0-00

Отзывы:

Похожие инструкции для PD765-6X0-00

Бренды по названию

Популярные бренды

Precision Digital Corporation PD765-6X0-00, Инструкция по эксплуатации

Результаты поиска

Содержание PD765-6X0-00

Отзывы:

Похожие инструкции для PD765-6X0-00

Бренды по названию

Популярные бренды