Precision Digital Corporation PD765-6X0-00 Скачать руководство пользователя страница 28

Страница: 28 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

Main Menu

The main menu consists of the most commonly used functions:

Setup

and

Password

•

Press

Menu

button to enter Programming Mode then press

ar-

row button to scroll main menu.

•

Press

Menu

, at any time, to exit and return to Run Mode. Changes

made to settings prior to pressing

Enter/Ack

are not saved.

•

Changes to the settings are saved to memory only after pressing

Enter/Ack

•

The display moves to the next menu every time a setting is ac-
cepted by pressing

Enter/Ack

Setting Numeric Values

The numeric values are set using the

Right

and

arrow buttons.

Press

Right

arrow to select next digit and

arrow to increment digit

value.
The digit being changed is displayed brighter than the rest.
Press the

Enter/Ack

button, at any time, to accept a setting or

Menu

button to exit without saving changes.

The decimal point is set using the

arrow button in the

Setup-decimal

point

menu.

9765

setu

pass

Run

Mode

4.00

Increment Digit

Value

Setting

Select Next Digit

Accept Setting

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание PD765-6X0-00








































































Результаты поиска

Содержание PD765-6X0-00

Отзывы:

Похожие инструкции для PD765-6X0-00

Бренды по названию

Популярные бренды

Precision Digital Corporation PD765-6X0-00, Инструкция по эксплуатации

Результаты поиска

Содержание PD765-6X0-00

Отзывы:

Похожие инструкции для PD765-6X0-00

Бренды по названию

Популярные бренды