PPI UniRec Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 27

background image

User Manual

UniRec

13

To exit the Set-up Mode and return to the MAIN Display Mode, press and release PAGE key.

Notes:

1. It is a must to press the ENTER key after altering the value of a parameter else the new value will not be registered / stored. That is, a

return to the MAIN Display Mode (by depressing PAGE key) without pressing the ENTER key will not store the altered value in the

UniRec memory and the previous set value will be retained.

2. If the UniRec is left in Set-up Mode for more than 30 seconds without any key operation, it automatically exits the Set-up Mode and returns

to the MAIN Display Mode.

«
...
13
14
15
16
17
...
»

Содержание UniRec




























Отзывы:

Нет отзывов

Похожие инструкции для UniRec

Бренд: Ebro Страницы: 32

Бренд: Extech Instruments Страницы: 14

ebro EBI 10 Series

Бренд: Xylem Страницы: 48

Бренд: Dwyer Instruments Страницы: 2

Бренд: retmon Страницы: 2

Бренд: YDOC Страницы: 120

Бренд: Calex Страницы: 5

Бренд: Ohkura Страницы: 61

Бренд: Data Harvest Страницы: 20

Бренд: Data Harvest Страницы: 28

EASYSENSE Q Advanced

Бренд: Data Harvest Страницы: 48

Бренд: Xylem Страницы: 50

Бренд: Omni Instruments Страницы: 9

Бренд: REED Страницы: 12

Бренд: Campbell Страницы: 32

VSN-MGR-CMML SERIES

Бренд: Power One Страницы: 25

PENDANT G UA-004-64

Бренд: Hobo International Страницы: 4

UX90-002 Series

Бренд: Hobo Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды