manualshive.com logo in svg

PowerTec 40Hp, Руководство пользователя

Поделиться
Скачать
PowerTec 40Hp Скачать руководство пользователя страница 54

48

 Fuel connector leakage

Inspecting fuel filter

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

 If you have any question about properly
  doing this procedure, consult your
  PowertecOutBoards dealer.

 Do not perform this procedure on a hot
  or running engine. Allow the engine to
  cool.
 
There will be fuel in the fuel filter. Keep
  away from sparks, cigarettes, flames or
  other sources of ignition.
 
This procedure will allow some fuel to
  spill. Catch fuel in a rag. Wipe up any
  spilled fuel immediately.

Spark plug gap:

 0.6–0.7 mm (0.024–0.028 in)

When fitting the plug, always clean the gas-
ket surface and use a new gasket. Wipe off
any dirt from the threads and screw in the
spark plug to the correct torque.

Spark plug torque:

 25.0 Nm (18.4 ft-lb) (2.55 kgf-m)

NOTE:
If a torque-wrench is not available when you
are fitting a spark plug, a good estimate of
the correct torque is 1/4 to 1/2 a turn past fin-
ger-tight. Have the spark plug adjusted to the
correct torque as soon as possible with a
torque-wrench.

Checking fuel system

Gasoline and its vapors are highly flam-
mable and explosive. Keep away from
sparks, cigarettes, flames, or other
sources of ignition.

Leaking fuel can result in fire or explo-
sion.
 Check for fuel leakage regularly.
If any fuel leakage is found, the fuel
  system must be repaired by a qualified
  mechanic. Improper repairs can make
  the outboard unsafe to operate.
Check the fuel lines for leaks, crack, or mal-
function. If a problem is found, your Powerte-
cOutBoardsdealer or other qualified mechanic 
should repair it immediately.

Checkpoints
 Fuel system parts leakage
 Fuel line joint leakage
 Fuel line cracks or other damage

WARNING

WARNING

WARNING

Maitenance

Содержание 40Hp





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды