manualshive.com logo in svg

PowerTec 40Hp, Руководство пользователя

Поделиться
Скачать
PowerTec 40Hp Скачать руководство пользователя страница 34

28

Reverse (automatic reverse lock and
power trim and tilt models)

When operating in reverse, go slowly. Do
not open the throttle more than half. Oth-
erwise the boat could become unstable,
which could result in loss of control and
an accident.

Tiller control models
1. Place the throttle grip in the fully closed
     position.

2.Move the gear shift lever quickly and
firmly from neutral to reverse.

Remote control models
1. Pull up the neutral interlock trigger (if
   equipped) and move the remote control
   lever quickly and firmly from neutral to
   reverse.

Reverse (manual tilt and hydro tilt
models)

When operating in reverse, go slowly. Do
not open the throttle more than half. Oth-
erwise the boat could become unstable,
which could result in loss of control and
an accident.

Tiller control models
1. Place the throttle grip in the fully closed
     position.

2.On models equipped with a tilt lock le-
ver, check that it is in the lock/down po-
sition.

WARNING

WARNING

Functioning

Содержание 40Hp





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды