manualshive.com logo in svg

PowerTec 40Hp, Руководство пользователя

Поделиться
Скачать
PowerTec 40Hp Скачать руководство пользователя страница 41

35

3.Push the power tilt / power trim and tilt
switch “ ” (down) to lower the outboard
motor to the desired position.

Cruising in shallow water
The outboard motor can be tilted up partially
to allow operation in shallow water.

Push the power tilt / power trim and tilt
switch “ ” (down) to lower the outboard
motor to the desired position.
Place the gear shift in neutral before us-
ing the shallow water cruising system.
Run the boat at the lowest possible
speed when using the shallow water
cruising system.
Use extra care when operating in re-
verse. Too much reverse thrust can
cause the outboard motor to lift out of
the water, increasing the chance of ac-
cident and personal injury.
Return the outboard motor to its normal
position as soon as the boat is back in
deeper water.

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

Procedure for hydro tilt models
1. Place the gear shift lever in neutral.

CAUTION

WARNING

Functioning

Содержание 40Hp





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды