PowerTec 40Hp Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 68

background image

13

The trim tab also serves as an anode to
protect the engine from electrochemical
corrosion. Never paint the trim tab as it
will become ineffective as an anode.

1. Trim tab
2. Bolt

Trim rod (tilt pin)
The position of the trim rod determines the
minimum trim angle of the outboard motor
in relation to the transom.

Tilt lock mechanism
The tilt lock mechanism is used to prevent
the outboard motor from lifting out of the
water when in reverse gear.

1. Tilt lock lever
To lock it, set the tilt lock lever in the “ 1”
(lock) position. To release, push the tilt lock
lever in the “1 ” (release) position.

Tilt support lever for power trim and

tilt or hydro tilt model To keep the outboard
motor in the tilted up position, lock the tilt
support lever to the clamp bracket.

CAUTION

Componentes básicos

«
...
17
18
19
20
21
...
»

Содержание 40Hp





































































Отзывы:

Нет отзывов

Похожие инструкции для 40Hp

Бренд: Panasonic Страницы: 26

Бренд: Faytech Страницы: 2

Бренд: Digital Equipment Страницы: 98

Бренд: MSI Страницы: 19

Бренд: ON Semiconductor Страницы: 20

Бренд: Phytec Страницы: 128

Бренд: Sapphire Audio Страницы: 50

Бренд: BESTEK Страницы: 45

Бренд: National Semiconductor Страницы: 22

Fatality H97 Killer series

Бренд: ASROCK Страницы: 109

Бренд: MSI Страницы: 91

MT9M031I12STCH-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: BCM Страницы: 59

Бренд: ASROCK Rack Страницы: 2

Бренд: CyberResearch Страницы: 286

Бренд: NXP Semiconductors Страницы: 138

PHANTOM GAMING Z790M PC LIGHTNING/D4

Бренд: ASROCK Страницы: 53

Бренд: Soyo Computer Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды