PowerTec 40Hp Скачать руководство пользователя страница 11

Страница: 11 / 68

upper half of the operating range at

full throttle with the maximum boat

load. If operating conditions such as

light boat loads then allow the en-

gine r/min to rise above the maxi-

mum recommended range, reduce

the throttle setting to maintain the

engine in the proper operating

range.

For instructions on propeller remov-

al and in-

stallation, see page 57.

General information

Start-in-gear protection

PowertecOutBoards outboard mo-

tors or PowertecOutBoards-ap-

proved remote control units are

equipped

with start-in-gear protection

device(s). This

feature permits the engine to be

started only

when it is in neutral. Always select

neutral

before starting the engine.

well over a range of applications, but

there may be uses where a propeller

with a different pitch would be more

appropriate. For a greater operating

load, a smaller-pitch propeller is

more suitable as it enables the cor-

rect engine speed to be maintained.

Conversely, a larger-pitch propeller

is more suitable for a smaller oper-

ating load.

PowertecOutBoards dealers stock a

range of propellers, and can advise

you and install a propeller on your

outboard that is best suited to your

application.

1. Propeller diameter in inches

2. Propeller pitch in inches

3. Type of propeller (propeller mark)

NOTE:

Select a propeller which will allow

the engine to reach the middle or

General Information

Содержание 40Hp





































































Результаты поиска

Содержание 40Hp

Отзывы:

Похожие инструкции для 40Hp

Бренды по названию

Популярные бренды

PowerTec 40Hp, Руководство пользователя

Результаты поиска

Содержание 40Hp

Отзывы:

Похожие инструкции для 40Hp

Бренды по названию

Популярные бренды