background image

21

Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com

Position bearing squarely onto the shaft 

applying force to the inner race of the 

bearing only, until bearing seats against 

shoulder of the shaft. Replace retaining 

rings (15) onto shaft. Replace top bearing 

(12) in the same manner.

Motor -

 Inspect windings for shorts 

and resistance. Check the continuity 

between the black and white wires of 

the temperature sensor. If found to be 

defective contact factory. Check rotor for 

wear, if rotor (6) or the stator (7) windings 

are defective, the complete motor must 

be replaced. Check that moisture sensor 

wires are secured to the electrode (36).

Motor Reassembly -

 Slide lower bearing 

and motor assembly into the bearing 

bracket (3) until bearing seats on the 

bottom. Position bearing cap (

on some 

models

) on bearing bracket, insert screws 

(19) with washers (20) and tighten to 16 

ft. lbs.

On other models

, insert retaining ring 

(8) into bearing bracket (3). Position 

motor and bearing assembly into pilot in 

motor housing (1) while feeding motor 

leads through opening in top of motor 

housing. Assemble upper seal as outlined 

above. 

Place o-ring (21) on motor housing (1) 

then intermediate (2), being careful not 

to damage o-ring. Insert screws (17) 

with washers (18) and tighten. Assemble 

lower seal as outlined above. Reassemble 

remainder of pump and fill with cooling 

oil.

Discharge Flange -

 Remove or replace 

discharge flang (56) by removing socket 

head screws (55), hex nuts (53) and 

washers (54).

Service

PF4SCC, 4SCD, 4SCE, 4SCF    

      

         

 

 Submersible Cutter Pumps

Содержание PF4SCC Series





























Отзывы: