Poulan Pro PZ4822 Скачать руководство пользователя | Manualshive

Страница: 47 / 75

background image

English-

46

MAINTENANCE

•

Install new or re-sharpened blade with
stamped "GRASS SIDE" facing towards
ground/grass (down) or “THIS SIDE UP”
facing deck and cutter housing.

•

Install and tighten blade bolt securely.

Torque blade bolt to 27-35 ft/lb
(35-45 Nm).

Adjusting the Mower Deck

Check the tire pressure before adjustment of
the mower deck, see “Checking Tire
Pressure” in Maintenance section.

Faulty mower deck adjustment will cause an
uneven mowing result.

IMPORTANT INFORMATION

Special blade bolt is heat treated.

Replace with a Husqvarna bolt if required.

Do not use lower grade hardware than
specified.

WARNING!

Before performing any service or adjustment checklist:

1. Engage the parking brake.
2. Place the Blade-switch in the disengaged position.

3. Turn ignition switch to “OFF” position and remove the key.
4. Make sure the blades and all moving parts have completely stopped.
5. Disconnect the spark plug wire from all spark plugs and place the wire where it
cannot come in contact with the plug.

WARNING!

Blades are sharp. Protect your

hands with gloves and/or wrap
blades with a heavy cloth when

handling.

«
...
45
46
47
48
49
...
»

Содержание PZ4822












































































Отзывы:

Нет отзывов

Похожие инструкции для PZ4822

Бренд: Han-Bond Страницы: 58

Бренд: Parkside Страницы: 34

Бренд: P.Lindberg Страницы: 111

Бренд: HTP Страницы: 20

Бренд: Laski Страницы: 35

Бренд: Cassese Страницы: 5

Бренд: NUTOOL Страницы: 22

Бренд: Stihl Страницы: 50

Бренд: Stihl Страницы: 276

Бренд: KAMBO Страницы: 48

Бренд: Far Tools Страницы: 15

Бренд: Han-Bond Страницы: 56

Бренд: IDEAL Страницы: 40

Бренд: Lassco Wizer Страницы: 13

Бренд: DeWalt Страницы: 44

Бренд: Makita Страницы: 64

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды