Poulan Pro PZ4822 Скачать руководство пользователя

Страница: 26 / 75

English-

OPERATION

Before Starting

•

Read the sections Safety Instructions
and Controls before starting the
machine.

•

Perform the daily maintenance before
starting (see Maintenance Schedule
in the Maintenance section).

•

Check that there is sufficient fuel in the
fuel tank.

•

Adjust the seat to the desired position.

The following conditions must be fulfilled
before the engine can be started:

•

The driver must be seated on the seat.

•

The blade switch for engaging the mower
blades must be depressed.

•

The parking brake must be on.

•

Both steering controls must be in the
locked (outer) neutral position.

Starting the Engine

Sit on the seat.

Raise the mower deck by depressing the
pedal forward to the locked position
(transport position).

Activate the parking brake.

8011-4842

Start conditions

4 1/2

3 1/2

2 1/2

1 1/2

8011-753

Raise the mower deck

Содержание PZ4822












































































Результаты поиска

Содержание PZ4822

Отзывы:

Похожие инструкции для PZ4822

Бренды по названию

Популярные бренды

Poulan Pro PZ4822, Руководство оператора

Результаты поиска

Содержание PZ4822

Отзывы:

Похожие инструкции для PZ4822

Бренды по названию

Популярные бренды