Poulan Pro PZ4822 Скачать руководство пользователя | Manualshive

Страница: 25 / 75

background image

English-

24

OPERATION

Operation

Read "Safety Instructions" section and following pages, if you are unfamiliar with the machine.

Training

Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering
capabilities.

We suggest when first operating the mower, use a reduced throttle speed and reduced ground speed by
NOT moving control levers to the furthest forward or reverse positions during initial operation, or until
operator becomes comfortable with controls. We also suggest first time users, or new users to ZeroTurn
mowers to become familiar with the mowers movement on a hard surface, such as concrete or blacktop
PRIOR to attempting to operate on turf. Until operator becomes comfortable with mower controls and zero
turning capability, they may damage turf due to over aggressive maneuvers.

To move forward and backward

The direction and speed of the mowers movements is effected by the movement of the control lever(s) on
each side of mower. The left control lever controls the left wheel. The right control lever controls the right
wheel.

First time users should push mower (see "Moving by Hand" in the "Operation" section) to an open, flat area,
without other people or vehicles/obstacles near by. In order to move unit under its own power, the operator
must be in the seat, start engine (see "Before Starting" in "Operation" section), adjust engine speed to idle,
disengage parking brake, do not engage blades at this time, rotate control levers inward. As long as the
control levers have not been moved forward or backwards, mower will not move. Slowly move both control
levers forward slightly, this will allow mower to start moving forward in a straight line. Pull back on control
levers to the neutral position and mower should stop moving. Pull back slightly on control levers, this will
allow mower to start moving backwards. Push forward on control levers to the neutral position and mower
should stop moving.

To turn to the right

While moving in a forward direction, pull the right lever back towards the neutral position while maintaining
the position of the left lever, this will slow the rotation of the right wheel and cause the machine to turn in
that direction.

To turn to the left

While moving in a forward direction pull the left lever back towards the neutral position while maintaining
the position of the right lever, this will slow the rotation of the left wheel and cause the machine to turn in
that direction.

To zero turn

While moving in a forward direction, first pull both control levers back until the mower stops or slows
dramatically. Then by alternating one lever slightly to the forward position and the other in the reverse
position.

IMPORTANT INFORMATION

When control levers are in the reverse
position they return to neutral when
released. This may cause the mower to
suddenly stop.

«
...
23
24
25
26
27
...
»

Содержание PZ4822












































































Отзывы:

Нет отзывов

Похожие инструкции для PZ4822

Бренд: maimin Страницы: 12

Бренд: Jenlis Страницы: 24

Бренд: Textron Страницы: 10

Бренд: Roberts Страницы: 2

Бренд: CNC Страницы: 16

Бренд: Xtool Страницы: 44

Бренд: Mafell Страницы: 96

ESSENTIAL OXYCUTTING

Бренд: Lincoln Electric Страницы: 42

Бренд: Onglematic Страницы: 4

Бренд: Univex Страницы: 7

Бренд: U-Line Страницы: 15

Бренд: Hiace Страницы: 12

Бренд: Standard Horizon Страницы: 49

Бренд: Tanaka Страницы: 18

Бренд: Zenoah Страницы: 16

Бренд: Hard Head Страницы: 9

SRM-210 - 02-04

Бренд: Echo Страницы: 34

Бренд: Makita Страницы: 117

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды