Poulan Pro PZ4822 Скачать руководство пользователя | Manualshive

Страница: 60 / 75

background image

English-

59

STORAGE

Storage

Winter Storage

At the end of the mowing season, the machine
should be readied for storage (or if it will not be in
use for longer than 30 days). Fuel allowed to
stand for long periods of time (30 days or more)
can leave sticky residues that can foul the
carburetor and disrupt engine function.

Fuel stabilizers are an acceptable option as
regards to the sticky residues that can occur
during storage.

Add stabilizer to the fuel in the tank or in the
storage container. Always use the mixing ratios
specified by the manufacturer of the stabilizer.
Run the engine for at least 10 minutes after
adding the stabilizer so that it reaches the
carburetor. Do not empty the fuel tank and the
carburetor if you have added stabilizer.

To ready the machine for storage, follow these
steps:

1.

Thoroughly clean the machine, especially
under the mower deck. Touch up damage to
the paint and spray a thin layer of oil on the
underside of the mower deck to avoid
corrosion.

2.

Inspect the machine for worn or damaged
parts and tighten any nuts or screws that may
have become loose.

3.

Change the engine oil; dispose of properly.

4.

Empty the fuel tanks or add a fuel stabilizer.
Start the engine and allow it to run until the
carburetor is drained of fuel or the stabilizer
has reached the carburetor.

5.

Remove the spark plug and pour about a
tablespoon of engine oil into the cylinder.
Turn over the engine so that the oil is evenly
distributed and then refit the spark plug.

6.

Lubricate all grease zerks, joints, and axles.

7.

Remove the battery. Clean, charge, and store
the battery in a cool place, but protect it from
direct cold.

8.

Store the machine in a clean, dry place and
cover it for extra protection.

Service

When ordering spare parts, please specify the
purchase year, model, type, and serial number.

Always use genuine Husqvarna spare parts.

An annual check-up at an authorized service
workshop is a good way to ensure that your
machine performs its best the following season.

WARNING!

Never store an engine with fuel
in the tank indoors or in poorly
ventilated spaces where fuel
vapor can come in contact with
open flames, sparks, or a pilot
light such as in a boiler, hot
water tank, clothes drier, etc.
Handle the fuel with care. It is
very flammable and careless
use can cause serious personal
injury and property damage.
Drain the fuel into an approved
container outdoors and far
away from open flame. Never
use gasoline for cleaning. Use
a degreaser and warm water
instead.

«
...
58
59
60
61
62
...
»

Содержание PZ4822












































































Отзывы:

Нет отзывов

Похожие инструкции для PZ4822

Бренд: Tally Dascom Страницы: 20

Бренд: Vito Agro Страницы: 52

Kongsberg XN IPC 2.0

Бренд: Esko Страницы: 165

Бренд: Hitachi Страницы: 21

Бренд: Hitachi Страницы: 40

MBM Triumph 5550 EP

Бренд: MBM Страницы: 41

Бренд: Orbitalum Страницы: 60

Бренд: SIZZIX Страницы: 36

Бренд: Royal Catering Страницы: 23

UNIVERSAL Comet CENTURY

Бренд: JB GURY Страницы: 32

Бренд: HSGM Страницы: 32

Бренд: HSGM Страницы: 32

Бренд: Pattfield Ergo Tools Страницы: 90

Бренд: CASTLE Страницы: 63

Бренд: Batavia Страницы: 6

Бренд: KISANKRAFT Страницы: 16

Бренд: Craftsman Страницы: 28

Бренд: Husqvarna Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды