Potterton Ultra DV 30 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 46

background image

Supplied By www.heating spares.co Tel. 0161 620 6677

40

REPLACEMENT OF PARTS

Manual No. 405/0101

REPLACEMENT OF PARTS - PAGE 40

9.26

TO REPLACE THE PROGRAMMER (IF FITTED)

Ensure that the electricity supply is off.

1.

With the control panel cover open, remove the two screws (one each side) securing the control panel to the case side
panels.

2.

Remove the four screws securing the bottom panel assembly (two each side) to the case side panels.
Carefully slide out the assembly away from the boiler, unclipping the neon from the back of the control panel, see
Fig. 35, before fully withdrawing the assembly.

Note:

Disconnect the wiring harness from the rear of the programmer before fully withdrawing the bottom panel

assembly.

3.

Remove the two screws securing the bottom of the programmer to the back of the control panel. Swing the programmer
up and unclip it from the top brackets.

4.

Fit the new programmer to the back of the control panel, locating the top two hinge pins into the brackets above the
opening then lowering it against the panel and securing it at the bottom using the two screws supplied with the
programmer.

5.

Carefully slide the bottom panel assembly into position (the bottom panel goes above the returns on the case side
panels), clip the neon, see Fig. 35, into its holder on the back of the control panel as the bottom panel is slid into
position. Secure the bottom panel to the side panels using the four screws previously removed. With the control panel
cover open, secure the control panel to the side panels with the two countersunk hd. screws previously removed.

Note:

Connect the programmer wiring harness to the rear of the programmer as the bottom panel is slid into position.

6.

Switch on the electricity supply, refer to the Programmer instructions and set the timer and programmes.

7.

Refer to the Lighting Instructions, section 8. Light the boiler and check the controls.

«
...
38
39
40
41
42
...
»

Содержание Ultra DV 30















































Отзывы:

Нет отзывов

Похожие инструкции для Ultra DV 30

Бренд: Magikitch'n Страницы: 2

ecoMAX pro 28 E

Бренд: Vaillant Страницы: 36

Vitorond 200 Type VR2

Бренд: Viessmann Страницы: 16

Бренд: Honeywell Страницы: 20

Logano plus SB745

Бренд: Buderus Страницы: 16

Бренд: abc Страницы: 23

Benchmark BMK 1000

Бренд: Aerco Страницы: 178

Бренд: croydon Страницы: 2

Бренд: croydon Страницы: 2

Бренд: Embassy Страницы: 80

VICTRIX 24 kW X

Бренд: Immergas Страницы: 208

MINI NIKE 24 3 E

Бренд: Immergas Страницы: 198

Бренд: Rapido Страницы: 52

Бренд: Truma Страницы: 5

Бренд: Potterton Страницы: 36

Osprey 2 CFL 125

Бренд: Potterton Страницы: 28

Vitoflame 300 VHG III

Бренд: Viessmann Страницы: 36

thermo condens WTC 15-A

Бренд: Weishaupt Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды