Potterton Ultra DV 30 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 46

background image

Supplied By www.heating spares.co Tel. 0161 620 6677

33

REPLACEMENT OF PARTS

Manual No. 405/0101

REPLACEMENT OF PARTS - PAGE 33

9.8

TO REPLACE THE FAN

1.

Gain general access as described in section 9.1.

2.

Remove the two screws securing the fan assembly to the flue hood, see Fig. 33. Carefully slide the fan assembly away
from the flue to disengage the flue tube sleeve from the flue. Withdraw the fan assembly, disconnecting the fan motor
and pressure switch leads.

Note:

If a Vertex Flue is fitted, slide the flue tube sleeve up into the flue to disengage it from the fan outlet.

3.

Remove the four screws securing the fan to the flue turret and remove the fan. Remove the flue tube sleeve from the
old fan. Ensure that the 'O' ring is in position on the fan outlet, then fit the flue tube sleeve over the fan outlet and push
it fully home. Secure the new fan to the turret with the four screws previously removed.

4.

Place the fan assembly on top of the flue hood with the outlet facing towards the flue and reconnect the leads, see
Fig. 14a, as follows:
Two violet leads to the fan motor.
Yellow lead to pressure switch No connection.
Red lead to pressure switch Nc connection.
Black lead to pressure switch C connection.
With the fan assembly resting on the flue hood engage the flue tube sleeve on the fan outlet into the inner tube of the
flue. Ensure that the base of the fan assembly is located under the returns at the rear of the flue hood. (For side exit
flue locate the base of the fan assembly under the returns first then slide the fan across into the flue).

Note:

If a Vertex Flue is fitted, slide the flue tube sleeve down out of the flue and over the fan outlet.

Secure the front of the fan assembly to the flue hood with the two screws previously removed.

5.

Reassemble the boiler as described in section 9.2.

6.

Refer to the Lighting Instructions, section 8 and light the boiler.

9.9

TO REPLACE THE AIR FLOW PRESSURE SWITCH

The air flow pressure switch is situated on the fan assembly.
1.

Gain general access as described in section 9.1.

2.

Carefully disconnect the flexible tube and the three leads from the pressure switch.

3.

Remove the two screws securing the pressure switch to its mounting bracket. Note which way the pressure switch is
secured to the bracket.

4.

Secure the new pressure switch to the mounting bracket with the screws previously removed and connect the flexible
tube to the

uppermost

tube on the pressure switch.

5.

Reconnect the pressure switch leads, see Fig. 14a, as follows:
Yellow to No, Red to Nc and Black to C.

6.

Reassemble the boiler as described in section 9.2.

7.

Refer to the Lighting Instructions, section 8 and light the boiler.

9.10

TO REPLACE THE MAIN BURNER INJECTOR

1.

Remove the burner as described in section 9.5, paragraphs 1 to 7.

2.

Unscrew the main injector from the burner manifold and remove the sealing washer.

3.

Screw in a replacement injector using a small amount of jointing compound and a new sealing washer.

4.

Replace the burner and reassemble the boiler as described in section 9.5, paragraphs 9 to 16.

«
...
31
32
33
34
35
...
»

Содержание Ultra DV 30















































Отзывы:

Нет отзывов

Похожие инструкции для Ultra DV 30

Бренд: Radiant Страницы: 60

Бренд: Alpha Страницы: 44

Duo-tec 2 Combi 40 GA

Бренд: Baxi Страницы: 20

Бренд: elco Страницы: 22

Prestige 24 Excellence

Бренд: ACV Страницы: 48

Бренд: tado° Страницы: 20

Бренд: STOKVIS ENERGY SYSTEMS Страницы: 65

Бренд: Garland Страницы: 40

RemaSol200SE-2S

Бренд: REMEHA Страницы: 80

Logano plus GB102

Бренд: Buderus Страницы: 12

Бренд: REMEHA Страницы: 2

Бренд: Flotec Страницы: 12

Бренд: Okofen Страницы: 32

Gold Combi 28 HE LPG

Бренд: Potterton Страницы: 12

Бренд: Potterton Страницы: 28

Бренд: ACV Страницы: 15

Бренд: BENEKOV Страницы: 39

Бренд: Knight Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды