Potterton Ultra DV 30 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 46

background image

Supplied By www.heating spares.co Tel. 0161 620 6677

13

INSTALLATION - REAR FLUE

Manual No. 405/0101

INSTALLATION - REAR FLUE - PAGE 13

front panel just below the depression. See Fig. 13.

2.

Remove the four screws (two at the top and two at the bottom) securing the inner case front panel and lift off the panel.
See Fig. 13.

Note:

When the inner case front panel is removed, the four case seal housing channels are not secured to the boiler

as they are retained in position by the front panel. Ensure that they are correctly fitted over the chassis edges before
the front panel is replaced.

3.

Remove the two screws securing the fan assembly to the flue hood. Withdraw the assembly, disconnecting

Fig. 14

the fan motor and pressure switch leads. See Fig. 14.

4.

Lift the boiler into position over the wall mounting plate. The boiler has two brackets on the back of the chassis at the
top, these should be located on top of the wall mounting plate to take the weight of the boiler.

5.

Secure the boiler to the wall mounting plate using the four M6 hex. hd. screws, supplied with the boiler.

6.

Remove the four screws securing the transit cover to the bottom of the boiler, see Fig. 13 and discard the cover and
screws.

7.

Ensure that the 'O' ring is in position on the fan outlet, then fit the flue tube sleeve, supplied with the boiler, over the fan
outlet and push it fully home.

8.

Place the fan assembly on top of the flue hood with the
outlet facing to the rear and reconnect the leads, see Fig.
14a, as follows:
Two violet leads to the fan motor.
Yellow lead to pressure switch No connection.
Red lead to pressure switch Nc connection.
Black lead to pressure switch C connection.

9.

With the fan assembly resting on the flue hood push it
towards the rear of the boiler, locate the flue tube sleeve
on the fan outlet into the inner tube of the flue/terminal
assembly and push the fan assembly fully home until the
base is located under the returns at the rear of the flue
hood, see Fig. 14.

10. Secure the front of the fan assembly to the flue hood with

the two screws previously removed.

11.

Proceed to section 3.13.

Fig. 14a

«
...
11
12
13
14
15
...
»

Содержание Ultra DV 30















































Отзывы:

Нет отзывов

Похожие инструкции для Ultra DV 30

Бренд: Radiant Страницы: 32

Бренд: Radiant Страницы: 28

Бренд: Radiant Страницы: 24

Ac-U-Temp ACMSS00507

Бренд: A.O. Smith Страницы: 4

EuroCombi Type C A23 MFFI

Бренд: Ariston Страницы: 32

Бренд: Main Heating Страницы: 83

Бренд: Bradford White Страницы: 40

Бренд: Lamborghini Caloreclima Страницы: 52

Бренд: Kenmore Страницы: 30

VITOCROSSAL 300

Бренд: Viessmann Страницы: 36

Бренд: U.S. Boiler Company Страницы: 96

Бренд: U.S. Boiler Company Страницы: 108

Бренд: ATH Страницы: 24

Бренд: ATH Страницы: 56

Бренд: kunzel Страницы: 32

MINI NIKE X 24 3 E

Бренд: Immergas Страницы: 36

Бренд: Immergas Страницы: 48

Бренд: Nature's Comfort Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды