Potterton Ultra DV 30 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 46

background image

Supplied By www.heating spares.co Tel. 0161 620 6677

Manual No. 405/0101

LIGHTING INSTRUCTIONS

29

8. LIGHTING INSTRUCTIONS - PAGE 29

See section 4.1 for boiler controls.
For access to the controls open the control panel cover (hinges down), if the internal programmer is fitted lower the
left hand cover after first opening the right hand one.

If a programmer is fitted refer to Programmer instructions to set the programmer.

Do not

attempt to light the boiler if the system pressure (see pressure gauge) is less than 0.5 bar. Repressurise the system

to 1.5 bar (see section 2.11, paragraph 4) and check for leaks, rectifying where necessary.
With the gas supply on and the electricity supply off.
1.

Turn the boiler thermostat control knob to 0.

2.

Switch on the electricity supply, set the programmer to continuous, if a programmer is fitted and check that all system
controls are calling for heat.

3.

Turn the boiler thermostat to 7. The automatic ignition sequence will start. The fan will start and after a purge period of
about 10 seconds a click will be heard indicating that the start gas solenoid has opened, the ignition sparks will also be
heard. The pilot will light and after a second or so the main gas solenoid will open and the main burner will light.

An amber neon, positioned between the pressure gauge and boiler thermostat, will light whenever the main burner is
alight.

Note:

The pilot burner is turned off every time the main burner is off. The ignition sequence is automatically activated

when the boiler thermostat requires heat.

4.

If a programmer is fitted, ensure that the timer is set to the correct time and the programme is set to the required
settings.

«
...
27
28
29
30
31
...
»

Содержание Ultra DV 30















































Отзывы:

Нет отзывов

Похожие инструкции для Ultra DV 30

MILBORNE 381 Series

Бренд: Hamworthy Страницы: 72

Бренд: U.S. Boiler Company Страницы: 180

Бренд: NeOvo Страницы: 44

Бренд: Dunkirk Страницы: 40

PRO-HT Tank Series

Бренд: Panasonic Страницы: 120

Бренд: Blodgett Страницы: 2

Бренд: RBI Страницы: 154

Бренд: Bryan Boilers Страницы: 4

Бренд: Bryan Boilers Страницы: 36

Бренд: Brute Страницы: 100

Бренд: Morco Страницы: 20

Бренд: Potterton Страницы: 36

Бренд: Lattner Boiler Company Страницы: 49

Бренд: Gledhill Response Страницы: 44

Бренд: Unical Страницы: 52

SZM W Plus 25kW

Бренд: SOLZAIMA Страницы: 53

DOMIcompact F 30 B

Бренд: Ferroli Страницы: 44

DOMIcondens F 24 D

Бренд: Ferroli Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды