POSEIDON PE 100-T Скачать руководство пользователя страница 34

Страница: 34 / 46

Instruction Manual

PE 100-T

Remedy

Cause

Trouble

High oil consumption

Piston rings, Pistons or cylinders worn
out

Replace defective parts, see chapter
4.4.9.

Intake filter clogged

Replace filter cartridge, see chapter
4.4.2.

Compressor too hot

Enhance cooling, see chapter 4.4.12.

Air escaping through cartridge safety
bore

Cartridge missing

Insert cartridge, see chapter 4.4.4.

Cartridge installed but O-rings defec
tive

Check/replace O-rings, see chapter
4.4.4.

Breathing air quality

Water concentration too high

Filter cartridge saturated

Replace cartridge, see chapter 4.4.4.

Ambient temperature too high

Check location; ambient temperature
max. +45

C (113

Intermediate and/oder final separator
dirty or clogged

Clean separator

Pressure maintaining valve faulty

Replace pressure maintaining valve

Oil concentration too high

Filter cartridge saturated

Replace cartridge, see chapter 4.4.4.

Unqualified lubricant being used

Replace oil with an approved brand,
see Lubricating oil list in annex.

Piston rings worn out

Replace piston rings

CO concentration too high

Filter cartridge saturated

Replace cartridge, see chapter 4.4.4.

Unqualified filter cartridge being used

Replace cartridge with CO removal
cartridge, see 4.4.4.

High CO concentration in the atmo
sphere (combustion gas, exhaust emis
sion...)

Change location, see chapter 3.1.

concentration too high

High CO

concentration in the atmo

sphere

Connect a CO

absorber (e. g. “Aero-

Guard”, see accessories catalog) to
the compressor

High CO

concentration in the filter

system

Scavenge the filter system before
filling, see chapter 3.3.4.

Содержание PE 100-T















































Результаты поиска

Содержание PE 100-T

Отзывы:

Похожие инструкции для PE 100-T

Бренды по названию

Популярные бренды

POSEIDON PE 100-T, Инструкция по эксплуатации

Результаты поиска

Содержание PE 100-T

Отзывы:

Похожие инструкции для PE 100-T

Бренды по названию

Популярные бренды