pleasant hearth PH35PS-B Скачать руководство пользователя страница 30

Страница: 30 / 44

7077-801F • 08/20

NOTICE:

These are guidelines for successful venting

of your pellet appliance. The more vertical rise you can

obtain in your system, the better it will perform. Horizontal

vent runs can accumulate ash and will need to be cleaned

more often. Try to keep them as short as possible.

We strongly recommend a minimum of 60 inches (1.5m)

vertical, however above the eave is preferred.

Both installations are approved for mobile home installations.

Must use 3 or 4 inch (76 to 102mm) “L” or “PL” Listed pellet

venting or Listed double wall pipe and authorized Outside

Air Kit in mobile homes. Single wall pipe is approved for

residential installations only.

Air Clearance to Pipe:

This appliance was tested with standard 3 inch (76mm)

Listed pellet vent.
Pellet pipe manufacturers Listed reduced clearance pipe

may be use for reduce clearance from 3 inch (76mm) air

clearance to no less than 1 inch (25mm) air clearance to

combustibles for approved Listed pellet pipe.

Follow pipe manufactures listed air clearances to

combustibles and installation instructions for all

reduced air clearances installations.

C. Vertical into Existing Class A Chimney

B. Through The Wall & Vertical - External -

Horizontal

A. Vertical - Interior - Typical Installation

Vent Systems

PREFERRED METHOD #1

Firestop

Flashing

Rain Cap

6 in.

(152mm)

Min.

Non-combustible Hearth Pad

follow pipe manufacture

listed clearance

12 in.

(305mm)

Minimum

Clean-out T

PREFERRED METHOD #2

Non-combustible Hearth Pad

Clean-out Cover

Tee

Wall Thimble

Support

Bracket

Every 60 in.

(1.5 m)

12 in.

(305mm)

Minimum

Rain Cap

Flashing

2 in. (5.08 mm) Minimum

6 in. (152 mm)

Minimum

Firestop

Flashing

Rain Cap

Non-combustible Hearth Pad

Follow vent manufacturer’s

clearances for reduced clearances

12 in. (305mm) Minimum

Ceiling Support

6 in. (152mm) Flue

Connector

6 in. (152mm) Class A

Chimney Connector

Adapter

6 in.

(152mm)

Min.

follow pipe manufacture

listed clearance

Clean-out T

Содержание PH35PS-B













































Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды

pleasant hearth PH35PS-B, Руководство пользователя

Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды