pleasant hearth PH35PS-B Скачать руководство пользователя страница 17

Страница: 17 / 44

[email protected]

7077-801F • 08/20

Altura Incorrecta de la Llama,

Llama Perezosa Alta

De Color Naranja

Altura Incorrecta de la Llama,

Llama Perezosa Alta

De Color Naranja

Les granules sont refoulées dans

le tuyau d’alimentation

Les granules sont refoulées dans

le tuyau d’alimentation

Trop de cendres dans le

foyer

Accumulation

trop importante

dans le foyer

11. Preparing Firebox for Non-Burn Season
• Frequency:

Yearly

• By:

Homeowner

a. Be sure the appliance is allowed to cool, has been

unplugged and the exhaust blower is off.

b. Remove all ash from the firebox and

vacuum thoroughly.

c. Paint all exposed steel, including cast-iron.

─ Purchase high temperature paint from your

local retailer.

─ Must use a high-temperature paint made

specifically for heating appliances.

12. Soot and Fly Ash: Formation & Need for Removal in

Exhaust Venting System.

• Frequency:

Yearly or more frequently depending on

ash build-up.

• By:

Qualified Service Technician/Homeowner

Be sure the appliance is allowed to cool, has been unplugged

and the exhaust blower is off.
The products of combustion will contain small particles of fly

ash. The fly ash will collect in the exhaust venting system

and restrict the flow of the flue gases.
At start-up if there is incomplete combustion, or if there is

a shutdown or incorrect operation of the appliance it will

lead to some soot formation. This will collect in the exhaust

venting system.
The venting (chimney) system may need to be cleaned at

least once a year or more often depending upon the quality

of your fuel or if there are any horizontal pipe sections.

Ash will build up more quickly in the horizontal sections

and elbows.

D. High Ash Fuel Content Maintenance

• Frequency:

As needed

• By:

Homeowner

Poor quality pellet fuel, lack of maintenance, or if the small

dial control is set to a less than optimum setting, poor

combustion conditions that make the firepot fill quickly with

ashes and clinkers.
This condition makes the appliance susceptible to overfilling

the firepot with pellets which may result in smoking, sooting

and possible hopper fires. The figure below shows an

example where the firepot overfills, pellets back up into the

feed tube and ash has accumulated in the firebox.
An inefficient and non-economical method of burning of fuel

caused by poor quality pellet fuel is shown below.
If the ash buildup exceeds the half way point in the firepot

IMMEDIATE ATTENTION AND CLEANING IS REQUIRED

Содержание PH35PS-B













































Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды

pleasant hearth PH35PS-B, Руководство пользователя

Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды