pleasant hearth PH35PS-B Скачать руководство пользователя страница 35

Страница: 35 / 44

[email protected]

7077-801F • 08/20

Symptom

Possible Cause

Corrective Action

Plug in appliance -

No response.

No Power to outlet.

5 amp fuse defective or blown

Snap disc tripped or defective.

Check circuit breaker at service panel.

Replace fuse.

Reset or replace snap disc.

Unit Will Not Light

No Fuel

Out of fuel.

Vacuum switch not closing, no vacuum.

Hopper lid open.

Defective hopper switch.

Feed System is Jammed

Feed motor not plugged in

No Igniter

Igniter not plugged in

Igniter not centered

Igniter defective

Firepot Plugged

Firepot dirty

Firepot in backwards

Too much debris in the bottom of the firepot

Check hopper. Fill with fuel.

Check exhaust blower is plugged in and operating.

Check vacuum switch is plugged in

Check vacuum hose is in good condition clear

and connected at both ends

Make sure venting system is clean

Make sure front door is closed

Check vacuum switch fitting on side of feed tube

for blockage

Close Hopper Lid

Check hopper switch operation

Inspect and un-jam the feed assembly

Reconnect feed motor

Plug the igniter in

Center the igniter

Igniter seated in chamber completely

Replace igniter

Clean firepot

Clean below the firepot

Put the firepot in the correct direction

Clean firepot

Fire starts but goes

out

Firepot is dirty

Exhaust path and/or venting is plugged

Exhaust sensor cannot read correct

temperature

Exhaust path is dirty

Exhaust probe is not attached to outlet

Exhaust probe is not plugged in to the board

Exhaust probe is defective (error code

may result)

Clean firepot. Check flue vent for obstruction

Inspect and clean exhaust path and venting clean

firebox including behind the baffles

Inspect and clean the exhaust outlet especially

the right side wall.

Remove the right side panel and inspect to see

if the exhaust probe is attached and tight against

the exhaust outlet

Plug the probe into the board

Replace the exhaust probe

Unit start and stops

frequently when

operating in the

automatic mode

Area were the unit is installed heats and

cools quickly depending on installation

configuration. Tight spaces also may have an

effect on the on/off cycling of the unit.

Ambient probe

Probe touching heated surface

Check the proximity to doors and windows and/

or insulation factor of the structure. If heat loss

is quick the unit may need to run on max or

minimum.

Inspect the probe and make sure it is not touching

a surface that heats and cools quickly. The

ambient probe has additional wire inside rear

cavity which can be used to increase the distance

from the unit.

With proper installation, operation, and maintenance your appliance will provide years of trouble-free service. If you do

experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the

corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.

Troubleshooting

Содержание PH35PS-B













































Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды

pleasant hearth PH35PS-B, Руководство пользователя

Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды