pleasant hearth PH35PS-B Скачать руководство пользователя страница 38

Страница: 38 / 44

7077-801F • 08/20

A. Component Function

1. Control Board

The control board is located on the right side of the

appliance behind the lower right side panel.

2. Convection Blower

The convection blower is mounted in the rear of the

unit. It pushes air up the rear of the firebox, across the

top and out the front. As the air moves past the firebox

it is heated.

3. Exhaust Blower

The exhaust blower is mounted on the left side of the

appliance. The exhaust blower is designed to pull the

exhaust from the appliance and push it out through the

venting system.

4. Feed System

The feed system can be accessed in two areas. To

access the auger spring, remove the cover in the

hopper. To remove the feed motor, remove the side

panel and motor cover plate in the rear of the unit.

5. Firepot

The firepot is made of a combination of stainless steel

and heavy duty cold rolled steel. It is removable to aid

in cleaning.

6. Fuse

The fuse is located on the control board. The fuse

will blow should a short occur and shut off power to

the appliance.

7. Dial Control

The dial control is attached to the right side of the

appliance. The large dial controls the heat output where

as the small dial below the large dial is the trim feature.

The LED blinks according to the state of the appliance.

8. Hopper Switch

The hopper switch is located in the upper right hand

corner of the hopper. This switch is designed to shut

down the feed motor whenever the hopper lid is opened.

9. Igniter

The igniter is mounted in the chamber in the rear of

the firebox below the convection blower. Combustion

air travels over the red hot igniter creating super heated

air that ignites the pellets.

10. Power Supply

The power cord connector in the rear of the unit. Check

the wall receptacle for 120 volt, 60 Hz (standard current).

Make sure the outlet is grounded and has the correct

polarity. A good surge protector is recommended.

Reference Materials

11. Exhaust Probe

The exhaust probe is mounted to the side of the

exhaust outlet in the rear of the unit. It senses the

temperature of the exhaust and allows the control

system to make decisions.

12. Ambient Probe

The ambient probe is located in the back panel. It

has extra wire to increase distance from appliance

if needed.

13. Snap Disc (Back Burn Protector) 200°F

Snap disc is mounted on the back of the auger tube

in the center of the appliance and has a reset button.

There are two grey wires connected to it. To access

it remove the right side panel. If the fire tries to burn

back into the feed system or push exhaust up the feed

tube, this snap disc will shut the entire system off.

Unplug the stove prior to resetting.

14. Vacuum Switch

The vacuum switch is located on the lower right side

of the appliance behind right side panel. There are

two red wires attached to it. This switch turns the feed

system on when vacuum is present in the firebox. The

vacuum switch is a safety device to shut off the feed

motor if the exhaust or the heat exchanger system

is dirty or plugged or if the firebox door is open or

exhaust blower failure.

15. Outside air inlet

The outside air tube can be attached to the 2” OD inlet

tube mounted to the rear of the firebox. To extend the

hose outside the unit there is a knockout plate that

must be removed.

When describing the location of a

component, it is always AS YOU FACE

THE FRONT OF THE APPLIANCE.

Содержание PH35PS-B













































Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды

pleasant hearth PH35PS-B, Руководство пользователя

Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды