pleasant hearth PH35PS-B Скачать руководство пользователя страница 12

Страница: 12 / 44

7077-801F • 08/20

LED

Color

Number of

Flashes between

pauses

Description

Notes

Green

Steady ON while

priming feed tube

(max time 2

minutes)

Feed Motor is running continuously.

(This primes the feed tube).

When priming the feed system and filling the

firepot,

DO NOT OVERFILL FIREPOT FOR

IGNITION

The unit will automatically go into

start up following the prime function.

Green

Steady ON while

burning

Room temperature is close to set point

and burning on lowest burnt rate.

Green

Unit is off and ready.

To start appliance, follow start up sequence.

Green

Blinks

Continuously

Appliance is in the start up/ignition

sequence or in shutdown.

During shut down, the blowers will shut off

when the exhaust temperature has cooled.

Green

Varies

When in the automatic mode, the number

of flashes between pauses indicates the

burn rate (1 for low up to 5 for high).

Adjust the dial control to change the desired

room temperature.

Amber

Steady ON

Appliance is set and running at either the

minimum or maximum power levels.

The unit will shut off only when the hopper

runs out of fuel, the user changes the dial

control to a different state, or the unit senses

an error.

Amber

Blinks

Continuously

Appliance is in the in shutdown sequence. During shut down, the blowers will shut off

when the exhaust temperature has cooled.

Red

Empty Hopper Alarm

This alarm is caused by the fire going out

from lack of fuel. See troubleshooting section

for more information.

Red

Exhaust Probe Alarm

Failed component error. See troubleshooting

section for more information.

Red

Ambient Probe Alarm

Failed component error. See troubleshooting

section for more information.

Red

Missed Ignition

There are a total of 2 tries per ignition

sequence. If after 2 tries there is no rise in

exhaust temperature this error will occur.

See the troubleshooting section for additional

information and correction.

Red

Exhaust Gas Over Temperature Alarm

The exhaust temperature exceed the

allowable limit. See the troubleshooting

section for more information and correction.

N. LED Color Coding Chart and Explanation

WARNING

Fire Risk

Do NOT operate appliance:

•

With appliance door open.

•

Firepot floor open.

Do NOT store fuel:

•

Closer than required clearances to combustibles to

appliance

•

Within space required for loading or ash removal.

Содержание PH35PS-B













































Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды

pleasant hearth PH35PS-B, Руководство пользователя

Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды