Platinum Access Systems BLSL2250 Скачать руководство пользователя страница 5

Страница: 5 / 36

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

PROTECTION AGAINST ENTRAPMENT

Usage Class

Gate Operator Category

Horizontal Slide, Vertical lift, and Vertical Pivot

Swing and Vertical Barrier (arm)

Primary Type*

Secondary Type*

Primary Type*

Secondary Type*

Vehicular I and II

Vehicular III

Vehicular IV

A, B1, or B2

A, B1, B2, or D

B1, B2, C, or D

A, B1, B2, C, D, or E

B1, B2, or D

A, B1, B2, D, or E

A, or C

A, B1, B2, or C

A, B1, B2, C, or D

Note - The same type of device shall not be utilized for both the primary and the secondary entrapment

protection means. Use of a single device to cover both the opening and closing directions is in accordance with

the requirement; however, a single device is not required to cover both directions. A combination of one Type

B1 for one direction and one Type B2 for the other direction is the equivalent of one device for the purpose of

complying with the requirements of either the primary or secondary entrapment protection areas.

Entrapment protection Types:

Type A:

Inherent entrapment protection system.

Type B1:

Provision for connection of, supplied with, a non-contact sensor (photoelectric sensor

or the equivalent).

Type B2:

Provision for connection of, or supplied with, a contact sensor (edge device or the equivalent)

Type C:

Inherent adjustable clutch or pressure relief device.

Type D:

Provision for connection of, or supplied with, an actuating device requiring continuous pressure to

maintain opening or closing motion of the gate.

Type E:

An audio alarm.

BLSL2250 Manual_Layout 1 2/10/2014 4:40 PM Page 5

Содержание BLSL2250





































Результаты поиска

Содержание BLSL2250

Отзывы:

Похожие инструкции для BLSL2250

Бренды по названию

Популярные бренды

Platinum Access Systems BLSL2250, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание BLSL2250

Отзывы:

Похожие инструкции для BLSL2250

Бренды по названию

Популярные бренды