Platinum Access Systems BLSL2250 Скачать руководство пользователя страница 7

Страница: 7 / 36

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

Important Safety Instructions

WARNING – To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with gate controls. Keep the remote control away from children.

3. Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH OF THE

MOVING GATE.

4. Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or stop when an object

activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator.
Failure to adjust and retest the gate operator properly can increase the risk of injury or death.

5. Use the emergency release only when the gate is not moving.

repairs to gate hardware.

7. The entrance is for vehicles only. Pedestrians must use separate entrance.

8. SAVE THESE INSTRUCTIONS

Maximum Gate Weight:

2200 lbs.

Maximum Gate Length:

50 feet

Opening Time:

12" per second

Power Requirements:

120 VAC Single Phase at 2 Amps or 220 VAC Single Phase at 1 Amp

Main Power:

Power Input: 100-240 VAC

Select 115 /230 VAC Single Phase

Built-in 24VDC battery backup
(7AmpHr 12VDC x 2)

Operating Temperature:

-20°C (-4°F) to 70°C (158°F)

Operator Weight:

210 lbs.

Operator Dimensions:

SPECIFICATIONS

BLSL2250 Manual_Layout 1 2/10/2014 4:40 PM Page 7

Содержание BLSL2250





































Результаты поиска

Содержание BLSL2250

Отзывы:

Похожие инструкции для BLSL2250

Бренды по названию

Популярные бренды

Platinum Access Systems BLSL2250, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание BLSL2250

Отзывы:

Похожие инструкции для BLSL2250

Бренды по названию

Популярные бренды