Platinum Access Systems BLSL2250 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 36

background image

24

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

Installation: Accessory Connections

ACCESSORY CONNECTIONS (continued):

Need to verify the proper connections before connecting the Radio Receiver.
The maximum voltage that the control board / battery can provide is about 28V
for external accessories. If there is an electrical shot in the power to the
accessories, the control board will protect itself by shutting down and will
remain shut down until the short is fixed.

Radio Receiver

Two modes of operation that a radio receiver
can control the gate:

Open-Close

By having the radio receiver connected as
illustrated and with the Timer OFF:
Every command of the radio transmitter
will control the gate as follow:
A. First command opens the gate
B. Second command CLOSE the gate if at

open position

C. Third command OPEN the gate
D. Any subsequent commands will continue

in the same order to control the gate.

This type of configuration is not recom-
mended for a commercial installations.

Open Only

By having the radio receiver connected as
illustrated and with the Timer ON:
Each command of the radio transmitter is
ALWAYS AN OPEN COMMAND to the gate.

RED

BLACK

GRAY

GRAY

MS-109950
Receiver

Linear MS-109950

Installation Diagram

BLSL2250 Manual_Layout 1 2/10/2014 4:40 PM Page 26

«
...
24
25
26
27
28
...
»

Содержание BLSL2250





































Отзывы:

Нет отзывов

Похожие инструкции для BLSL2250

Бренд: FAAC Страницы: 25

Бренд: FAAC Страницы: 15

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 30

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: White Rose Страницы: 29

Бренд: Tenpilot Страницы: 24

Open Master 404

Бренд: Krups Страницы: 8

Easy Touch 681131066235

Бренд: GE Страницы: 8

Бренд: Essmann Страницы: 10

Бренд: ProfiTech Страницы: 8

Бренд: CAME Страницы: 16

Бренд: BelFox Страницы: 14

Бренд: BelFox Страницы: 34

Axess Pro Series 1101

Бренд: Automatic Technology Страницы: 40

Бренд: Iijima Страницы: 4

Бренд: RAWLINK Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды