Platinum Access Systems BLSL2250 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 36

background image

20

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

Installation: LIMIT SWITCH SET-UP

LIMIT SWITCH SET-UP (continued):

LIMIT SWITCH

CONNECTIONS

The Limit Switches are

pre-wired. Should the

wires become dis-

connected, use this

diagram to reconnect

them.

OPENING/CLOSING SETUP

1. Setup the limit switches manually at the desired open and close position.
2. Allow the gate operator to run a full open and close cycle (from limit to limit)

without interruption.

Note: During the first full open and close cycle, the gate operator will run at low

speed. During subsequent cycles, the gate operator will speed up at start and

slow down prior to reaching its limits.

3. Verify that the gate opens and closes to the desired position.

Note: When slightly adjusting the open or close limit position(s), the operator will auto-

matically adapt the changes. When relearning is needed, push and hold "RESET"

button for 3 second, the machine will return to original state, and be ready for learning.

Black

Red

Right Limit

Switch

Left Limit

Switch

Gree

n

White

BLSL2250 Manual_Layout 1 2/10/2014 4:40 PM Page 22

«
...
20
21
22
23
24
...
»

Содержание BLSL2250





































Отзывы:

Нет отзывов

Похожие инструкции для BLSL2250

Бренд: SDC Страницы: 12

Commander Extreme MS125MYQ

Бренд: Merlin Страницы: 24

Бренд: D.A.C.E Страницы: 16

MhouseKit SL10S

Бренд: Nice Страницы: 132

Бренд: BEA Страницы: 2

Бренд: Delton Страницы: 8

Бренд: Roma Страницы: 36

Бренд: Elvox Страницы: 36

Бренд: tau Страницы: 44

Бренд: Dea Страницы: 56

AccessMaster Security+ M150

Бренд: Chamberlain Страницы: 36

Бренд: Roger Technology Страницы: 16

Бренд: CAME Страницы: 38

Walk-n-Cut 76503

Бренд: Hamilton Beach Страницы: 10

Бренд: Accessmatic Страницы: 48

Бренд: CAME Страницы: 12

SPACEMAKER EC75 Series

Бренд: Black & Decker Страницы: 2

RADIOSENS RSEC3

Бренд: JCM Technologies Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды